LINKSYS WAP1200AC AC1200 Wi-Fi ACCESS POINT

245.00 SR
(السعر غير شامل الضريبة)
(excl, VAT)
متوفر بالمخزون
نقاط مكافأة: 245 نقطة
التوصيل
طرق الدفع
مميزاتنا

ضمان الوكيل .

SMS تنبيهات .

استبدال واسترجاع .

طرق دفع مختلفة .

أفضل الأسعار .

User-added image

The Linksys WAP1200AC AC1200 Wi-Fi Access Point is the latest in the AC-series access points, which utilizes the Cross Band technology.  It can be used as a Wireless Range Extender or a Wired Access Point.  Both functions maximize simultaneous use of the 2.4 GHz and 5 GHz bands for high-speed data transfer, uninterrupted streaming, and gaming.  
 
With the Linksys WAP1200AC, you can have video conference and share files without interruption, even when the rest of your family is gaming and streaming videos.

User-added image
  • Antenna positioning is done depending on the type of home you have.
IMPORTANT:  The antennas are fixed and can ONLY rotate at 180 degrees.  Do NOT force the antennas too far back, otherwise, they will break.
  • For Single-story homes - Both antennas should be pointing down.
NOTE:  For illustration purposes, the Linksys RE6700 is used in this example.
 
User-added image
  • For Multi-story homes - One (1) antenna should always be pointing down to provide coverage for the current floor.  The second antenna (any antenna) should be positioned differently depending on where the Linksys WAP1200AC is located and where the coverage is needed.
NOTE:  For the most part, position one (1) antenna at 45 degrees as shown in Position A below.  If there are issues with coverage, move the antenna at about 50-55 degrees down as shown in Position B. 
 
User-added image
 
Position A can be used if the Linksys WAP1200AC is in the middle of the house.
 
User-added image
 
Position B can be used if the Linksys WAP1200AC is connected to an outlet located at the farther side of the house.
 
Side Panel
 
User-added image
 
User-added image Wi-Fi Protected Setup™ (WPS) button – Uses the WPS technology to automatically and securely add wireless devices to your network.

User-added image Reset button – Press and hold for 10 seconds to reset the Linksys WAP1200AC to factory default settings.
 
Bottom Panel

 
User-added image

User-added image ETHERNET port – Connect an Ethernet-enabled device to the network using either a Cat 5 or 6 Ethernet cable.
 
Product Features
  • Concurrent dual-band (2.4 GHz and 5 GHz)
  • 802.11ac Wireless technology
  • Compatible with 802.11 a/b/g/n
  • Data Rate of up to 300 Mbps for 2.4 GHz and up to 867 Mbps for 5 GHz
  • Two (2) external non-detachable antennas
  • 2 x 2 Spatial Streams
  • One (1) 10/100/1000 Fast Ethernet port with auto MDIX sensing
  • Spot Finder technology (on Range Extender Mode only)
  • Wi-Fi Protected Setup™ (WPS)
  • Browser-based Setup (BBS)
  • Cross Band technology  (on Range Extender Mode only)
  • Beamforming technology
LED Behaviors

User-added image Power / WPS LED:
  • OFF – There is no power on the Linksys WAP1200AC.
  • Blinking Green / Yellow – The Linksys WAP1200AC is starting up, resetting to factory defaults, upgrading its firmware, or the WPS connection is in process.
  • Solid Green / Yellow – The Linksys WAP1200AC is ready to use.
  • Solid Amber / Red – There is a weak connection with the router.
  • NOTE:  To fix this issue, unplug the Linksys WAP1200AC and move it closer to the router.
  • Blinking Amber / Red – The Linksys WAP1200AC is not connected to the router, or the WPS pairing failed.
NOTE:  To fix this issue, make sure that your router has an active Internet connection and the Wi-Fi is turned ON.  If the router is working fine, unplug the Linksys WAP1200AC then move it closer to the router.  Plug it back in, wait for one (1) minute, and reconnect to your network.

User-added image Ethernet LED – It lights up solid Green when an Ethernet device is connected and active.  It will blink when sending or receiving data over the Ethernet port.
 
Product Requirements
  • Wi-Fi enabled computers or mobile devices
  • AC power outlet
  • Ethernet router or switch with available RJ45 Ethernet port and RJ45 Cable for Access Point mode or wireless network for Range Extender mode
  • For browser configuration:
    • Internet Explorer® 8 or higher
    • Safari® 5.1 for Mac® or higher
    • Google Chrome™ 25.0 or higher
    • Firefox® 20 or higher  

 

الشركة المصنعة
LINKSYS
مواصفات المنتج العامة
قوة الانتينا
  • 2.4GHz: 3.97 / 5GHz: 5.97
المعيار اللاسلكي
  • Dual-band 802.11 a/b/g/n/ac
Antenna Type
  • External DiPole
التردد
2.4GHz: 2412-2472 MHz
Ports
  • Gigabit Ethernet Port

لم يتم العثور على أي تقييمات

خصومات / الأكثر مبيعاً

  • الأكثر مبيعاً
  • الخصومات
  • شوهد مؤخرا
 
 
 
التوصيل السريع والآمن

التوصيل داخل المملكة ودول الخليج

ضمان الخدمة والجودة

جميع منتجاتنا أصلية ذات جودة عالية

الاسترجاع خلال 7 أيام

لديك 7 أيام لاسترجاع المنتج